Data Collection

What's new

    Boards

    BoardLabelBatteryIMUMicFlashFWUSER

    No boards connected.

    No board selected.

    Endurance test

    Tests only the selected board with finite 10% clicks. Keep the wired controller clear. A reconnect may need a USER press.

    Add each board in turn; pick one to see it below. Drag a board by its ID to move it in the list. Labels and the order are remembered per board in this browser, and the label names its folder in recordings.

    Pairing: a board pairs only within 2 minutes of a double press of its USER button, a phone held to it, or while it's paired with nothing. Your computer then asks for a 6-digit code: it's in the board's USB console (task monitor), and a phone held to the board opens this page showing it. A new code follows every pairing.

    ⏾ (or holding USER for 5 s) puts a board to sleep; pressing USER wakes it.

    Recording

    No folder: files download instead.

    Connect a board first.

      Haptics TacHammer

      Plays a cue on the selected board's TacHammer (a Drake LF through a MAX98357A amp), or on every board at once. The three Drake cues are the friction, impact and deep rumble tuned on the recording board, held to 70% as they were there. The patterns are the Actuators dialog's test waveforms. Stop stops every board's actuators.

      A board with the amp on its header (SD_MODE on D1, powered from USB, no joystick) needs Wiring set to Header amp in its hardware profile, under the board list. A board's own drive ceiling caps every cue too.

      Cues themselves aren't recorded: the IMU and microphone record what the board felt and heard.

      With several boards, choose a clock source first (Settings › Clock sync): the others record their time against it about once a second, and task align lines them up on it afterwards.

      This computer: a board that drops out is reconnected and carries on in the same files; one connected after Record joins in. The recording is kept in this browser as it runs, so if the page closes it's offered for saving next time.

      With a folder chosen (remembered in this browser), each session is saved as a folder of its own. Without one, its files download one by one as session__board__imu.csv and so on. Replay opens either.

      Orientation VQF, 6-axis At rest

      Roll –Pitch –Yaw –

      Motion gyro bias removed XYZ

      Acceleration g · ±2
      Angular rate °/s · ±250
      −4 snow

      The traces are the last 4 s of every 4th sample, X, Y and Z in the colors keyed above. Recordings keep every sample, uncalibrated and with the gyro's bias left in.

      Microphone peak per ms, dBFS

      Level –
      Spectrum kHz–
      −4 s−2 snow
      Speech to text on this computer

        The level is the loudest sample in each millisecond, which a recording on this computer keeps (the boards' flash doesn't). The spectrum is for watching only (not recorded): brighter is louder.

        Talk sends the board's microphone to this page, up to 30 s at a time; its live data pause meanwhile. Whisper (tiny.en, English) turns it into text on this computer: the audio goes nowhere else. The speech model downloads the first time and the browser keeps it.

        Replay no session open

        Open a session's folder, or drop it on the page, to plot it.
        ShowBoardLengthSamplesRateLostPresses

        Open a session's folder, or a folder holding several (then pick one from Session, newest first), or drop either anywhere on the page. Files… (or a drop of files) is for a session that was downloaded rather than saved to a folder: take all of its session__… files. Of Chrome's numbered copies, imu (1).csv and so on, the newest is used.

        The session opened last opens again next time; Chrome asks once per visit to let the page read it. The files are only read by this page and never leave the computer.

        Signals

        Zoom in time: with the pointer over the lanes, slide two fingers up or down on the trackpad (or turn the mouse wheel). It zooms in on the time under the pointer. Pinching works too.

        Zoom up and down: the same while holding Option (⌥), or with the pointer over the numbers at a lane's left edge. It zooms in on the value under the pointer, on every lane at once.

        Pan: slide two fingers sideways, or drag a lane (up and down too, once zoomed vertically). Double-click a lane (or press Whole session) to see it all again.

        Keys, with the lanes clicked first: ← → pan (Shift for a whole screen), + and − zoom in time, ↑ ↓ zoom up and down, 0 shows it all.

        Two fingers up or down zoom about the pointer (with Option, up and down), sideways or a drag pans, double-click shows the whole session (more under the ⓘ by Whole session).

        Quaternion is VQF's orientation as recorded (W, X, Y, Z, unit length); Orientation is the same as roll, pitch and yaw, with yaw counted from the first sample.

        Shading is USER held and red ticks are lost samples. The strip at the bottom is the whole session: click or drag it to move.

        Update firmware

        No image chosen

          No boards connected: add them first.

          Ticked boards update together, about 30 s each, then restart into the new firmware and reconnect. One that doesn't come up on it rolls back by itself. Cancel stops them while they upload, before any board restarts; closing this keeps them going.

          Calibrate the IMU

          Accelerometer: at rest it should read exactly 1 g whichever way up it is. Six faces, each still for 2 s, give its offset and gain on every axis. They needn't be square: anything within 25° counts, and the fit doesn't assume square.

          Gyroscope: ten whole turns are 3600°, whatever speed you turn at. What the gyroscope adds up to over them, against that, is its gain. The board must stop exactly where it started, so line it up with a mark or an edge first, and turn about the axis being tested, which keeping it on a flat table does.

          The turns are timed by the board's own clock, so the result doesn't depend on its sample rate, and the gyroscope's offset is measured before and after, so it doesn't depend on that either.

          Save after the accelerometer, and after one, two or all three gyroscope axes. A board keeps what it was given until it's calibrated again or cleared.

          Accelerometer

          Joystick curve

          How fast the cursor moves for how far the stick is pushed. Inside the dead zone it doesn't move at all, which keeps a stick that doesn't quite rest at its centre from creeping the cursor.

          Past it, the speed is the slow gain times the push plus the fast gain times the push cubed. The slow gain sets fine control near the centre, the fast gain how quickly a full push crosses the screen. A full push moves the two together, in counts a second (a count is about a pixel at normal tracking speed), times the mouse speed.

          Each change is saved on the board when you let go of a slider, so you can try it on the cursor straight away. The dot shows the stick's push roughly: the board learns its stick's centre and reach for itself.

          Actuators

          Start the TacHammer at a low level: it hits its end stops hard. Pulses (click, knock, heartbeat) are felt as taps, sines as a buzz.

          The servo follows the slider while you drag it. Its plot shows the command (blue) against the position its feedback wire reports (orange) over the last 10 s. Spring first measures how the feedback moves, then holds the centre and gives way when you push it.

          Closing this dialog stops everything, and the servo goes limp.

          TacHammer

          Servo

          Inputs